HIGH-LEVEL 12 dB/OCTAVE CROSSOVER DESIGN CHART
Values selected for typical loudspeakers
and their associated impedance characteristics.

FREQUENCY 4 OHMS 8 OHMS    in Hz CAP. COIL CAP. COIL 

Frequency 4 ohms 8 ohms
50 564 /18  283 /36
60 472 /15 236 /30
70 400 /12.8 200 /25.7
80 354 /11.3 177 /22.6
90 313 /10 156 /20
100 283 /9.0 141 /18
120 236 /7.5 118 /15
150 188 /6.0 94.5 /12 
200 141 /4.5 71 /9.0
250 113 /3.6 56.4 /7.2
300 94.5 /3.0  47.2 /6.0
350 80.5 /2.57 40.3 /5.14
400 71 /2.26 35.4 /4.52
450 62.5 /2.0 31.3 /4.0
500 56.4 /1.8 28.3 /3.6
600 47.2 /1.5 23.6 /3.0
700 40 /1.28  20 /2.57
800 35.4 /1.13 17.7 /2.26
1000 28.3 /0.9 14.1 /1.8
1200 23.6 /0.75  11.8 /1.5 
1500 18.8 /0.6  9.45 /1.2
2000 14.1 /0.45 7.1 /0.9 
3000 9.45 /0.3  4.72 /0.6
5000/ 5.64 /0.18 2.83 /0.36 
5500 5.13 /0.16 2.56 /0.33
6000 4.72 /0.15 2.36 /0.3
7000 4.0 /0.13 2.0 /0.26
8000 3.55 /0.11 1.8 /0.23
9000 3.13 /0.1 1.56 /0.2
10000 2.83 /0.09 1.41 /0.18

 



All capacitor values are in microfarads ( uF ).
All coil values are in millihenrys ( mH ).

NOTE: as the chart shows, values scale up and down directly, in
octaves, for changes in impedance of half or double, and by factors of
ten for frequency factors of ten. To determine crossover points higher
or lower than those shown on the chart, select the proper impedance (4,
8, or 16 ohms) then look up the frequency in the left column that is
ten times or one tenth of your desired frequency and simply move the
decimal points to the right or to the left to determine the correct
values. Higher frequencies require moving the decimal points to the
left, and lower frequencies require moving the decimal points to the
right.

EXAMPLE: 8-ohm crossover for 80 Hz subwoofer will require a 177 uF
capacitor and a 22.6 mH coil.

CROSSOVER INDUCTORS
Wire gauges used for winding air-core inductors should be chosen
so that crossover-associated power losses are minimized. Look at the
wire table to get an idea of the approximate added resistance you will
have when using a particular wire gauge to wind inductors. This added
resistance not only spoils amplifier damping factors, but can also de-
tune vented low frequency loudspeaker systems. Use the heaviest gauge
double form var insulated wire possible for winding inductors. If you
are buying ready-made inductors, don't be misled; the coil in the 80 Hz
subwoofer example above would be 100-200 mm (4"-8") in diameter and
weigh from 2 to 8 kg (4-16 lb) depending on wire gauge. An RF coil
designed for use in radios may have the same inductance (at high
frequencies) and be wound on a pencil-sized bobbin with fine wire.
This type of inductor will definitely not work in a crossover with
loudspeaker loads connected.
Make sure your coils are wound tightly with neatly stacked layers
which produce a winding cross section that is approximately square.
The bobbin used to wind coils for crossovers should have an inside coil
diameter which is twice the coil width or thickness, and the outside
coil diameter should be wound out to four times the coil's width, or
twice the inside diameter. After winding, saturate the coil in lacquer
or resin. After drying, wrap it with stretchable cloth tape and give
it another coat of lacquer. Keeping the layers stacked neatly and the
coil cross section square, helps minimize the wire resistance for a
given inductor value.
Use a mounting board made of non-magnetic material such as
masonite or plywood. Place coils on your crossover mounting board so
that all coils are facing each other at right angles to minimize
magnetic inductive coupling. Some distance between coils helps reduce
coupling also. Keep any coils away from large metal surfaces. Place
insulating tubing over coil lead out wires to prevent shorts in case of
speaker system vibration. On long lead out wires, clamps or blobs of
hot glue should be used to dress wires securely to the mounting board.

CROSSOVER CAPACITORS
Capacitors used in crossovers MUST BE NON-POLARIZED and for best
sound must have low self-inductance. High-quality 100-200 volt rated,
foil wound Mylar capacitors should be used and should be individually
paralleled by 0.01 microfarad polypropylene or polystyrene capacitors
to short out the high-frequency self-inductance of coil formed by the
many layers of foil winding inside. Capacitors should be placed on the
crossover mounting board away from heat-producing power resistors.
Capacitor placement is not critical in terms of electrical operation of
the crossover, however, capacitors should be attached so that speaker
system vibration will not break their leads by bending and metal
fatigue.

 

River Oaks Car Stereo
Tech Resources
History 101
Car Warranties
Installer Mailing List
Fiber Optic AUX Input
 
Setting Amplifier Gain
Aiming Woofer Box
Cone Area
Ohms Law Chart
Transfer Function
Pre-Amp Voltage
Diversity Antennas
Woofer Box Size
Frequencies and Wavelengths
Frequency Spectrum
Speaker Resonance
Head Unit Power
Audio Imaging
Audio Loudness Control
FM Multipath
Watts
RCA cs Cat5
Crossovers
Woofer Box Perfection
Tight Bass
Speaker Impedance
Speaker Specs
Test Equipment
 
Good Sound
Poor Car Stereo
Phonetic Alphabet
River Oaks Car Stereo Newspaper
Woofer Box Strength
CB Radio
Fuses
Giant Loudspeakers
Amateur Radio
Amateur Radio Installations
Head Rest Video
Test
Tool List
Proper Grounding
Radio Spectrum
Short Wave Radio
Perfect Installer
Trunk Rattles

WE SHIP DIRECTLY TO YOU
713-626-7627 or 713-626-7628

If you have any questions or problems feel free to contact us for help or directions.
We are located at 4129 Richmond Ave. Houston TX 77027

Database and this Website Copyright © 1995-2024 Eddie Runner - Installer.com Websites Hosted by TXSoft

This Amazing Domain is for sale - Owner wants to retire - We have been online since 1995